Antique John Deere Tractor Parts

    Antique John Deere Tractor Parts - Electrical Parts

Cover Band (1-5/8" Wide)

Fits Delco 2 & 3 Brush Generators, 4-1/2" dia - Cover band encircles field case and "clips" to itself, "Rolling-Up" the Opposite End from the clip shortens the band and increases clamp tension when "clipped", Delco #816340

6 Volt (4 Terminal) External Voltage Regulator

Fits John Deere Tractor: A, AO, AR, B, BO, BR, G, L & LA Note :Can replace tractors with cut-outs by using Voltage Regulator Conversion Kit
below) - 231-12028

John Deere 6 Volt Voltage Regulator
4 Terminal

Fits John Deere Tractor: M, 40, 70, 320, 330, 420, 430 & 440 using generator #1101852, Replaces #AM2702T & Regulator #1118291, #1101308, #1101780 - 231-12030

John Deere Voltage Regulator Conversion Kit

Fits John Deere Tractor: A, AO, AR, B, BO, BR, G, H, L & LA (Used with ABC152 & ABC153 Voltage Regulators when replacing Delco-Remy cutouts 1116766, 1116807, 1116809 & 1116816 or Cut-Outs 5839, 5851 & 5894 therefore modernizing the generator system (For JD generators 1101356, 1101371, 1101377 & 1101385) (Conversion Kit Installation"F" terminal on regulator to "F" terminal on generator)

John Deere 12 Volt (4 Terminal) External Voltage Regulator (Saddle Mount)

fits John Deere Tractor: A, D, G, 50 & 60, Combines 55, 65 & 95 using generators 1100955, 1101956, 1101777, 1101784 & 1947579, Replaces regulators #1118266, #1101306, #1101791 & #1101792 - 231-12031

John Deere 12 Volt (3 Terminal) External Voltage Regulator ( Saddle Mount)

Fits John Deere Tractor: A, G, 50, 60, 70, 520, 530, 620, 630, 720 & 730 using generator #1100309, Replaces regulator #1118783 - 231-12033

Voltage Regulator, Mechanical, 4 Terminal, Flat Mount 24 Volt

Fits John Deere Tractor: 3010, 3020, 4010, & (4020 up to sn # <-222,999) (use w/ Delco Generator #'s 1103026, 10459574, 1103021, JD #'s AR11302 & TY1447) Replaces AR30155, 1119282, 1118957

Voltage Regulator, Mechanical, 3 Terminal, Flat Mount 12 Volt

Fits John Deere Tractor: Gas & LP 3010, 3020, 4010, (4020 up to sn # <-222,999) (Use with Delco generators 1100413) Replaces 1118896, 1119135 & AR11304

Regulator Shock Mounts

Mount Kit for regulators 231-12008 & 231-12011 - Replaces AT21632

Antique John Deere Tractor Parts - Alternator

One Wire 63 Amp Alternator

(NEW not Rebuilt) (10 square inch surface area, 6-1/4 inches housing diameter, 2-1/2 inches pulley diameter, 5/8 inch belt width)
NOTE: Must rev engine to 800 - 850 RPM in order for unit to self excite. INSTALLATION: Run a wire from the alternator through the amp gauge to the positive side of the battery.

Alternator Pulley only

For ABC418 Alternator above. (.670" shaft diameter, 2-1/2 pulley O.D., 5/8" belt width)

Mini 42 AMP Alternator W/Pulley & Diode

Fits John Deere Tractor: 4-1/2" Dia housing --- 2-1/2" Dia Pulley --- .590" OD shaft for drive pulley --- 3/8" Belt width --- 3-Wire internal regulator with wiring instructions --- For tractors requiring a smaller Dia alternator for clearance --- New, not rebuilt --- To convert 6-V to 12-V system --- For negative ground systems only J400-52001

Antique John Deere Tractor Parts - Universal Alternator Mounting Kit

Universal Alternator Mounting Kit

(Used when switching from a generator to an alternator)
NOTE - Does not include the top adjusting bracket. J8001001

Universal Top Adjusting Bracket for Alternator Or Generator

Fits John Deere Tractor: 7/8" WIDE, FARTHEST END OF SLOT TO CENTER OF MOUNTING HOLE IS 8 1/4", 3/8" MOUNT HOLE, 3 3/4" SLOT LENGTH