Brake, Clutch, Differential, Rear Axle & Transmission
IHS493 Round Clutch Inspection Plate - 4-3/16" O.D.
|
IHS627 Clutch Dust Cover (Release Bearing Grease Hole Cover) - 2.025" O.D.
|
ABC337 Lined Brake Band - Brake rod attached to lining2 required per tractor
|
ABC269 Lined Brake Bands - Brake rod unpins from lining, 1 lined brake band per wheel
|
MIS1131 Brake Riveting Tool - 1-1/4" throat depth1/8" diameter rivet punch5/16" anvil
|
MIS2547 Deep Throat Brake Rivet Tool - 3-3/8" Deep Throat2-1/8" high throat
|
IHS880 Clutch and Brake Pedal Return Spring - OVERALL LENGTH 4-1/2"
|
IHS5800 Snap Ring - Fits Cub & Loboy on Belt Pull Drive Housing, M, MD< Super M, Super MD, Super MDTA, MDV, Super MTA, MV on Trans Main Shaft Bearing, O6, ODS6, OS6, Super W6, Super W6TA, W6, Super WD6, WD6 on Trans Main Shaft Pilot Bearing
|
IHS014 Bake Drum - Does not include set screw or jam nut.
|
ABC1510 Outer Rear Axle Oil Seal - Must reuse your seal retainer 2.125" ID 3.066" OD 0.510" width
|
ABC1512 Final Drive Oil Seal - 1.750" I.D., 2.632" O.D., .500" Width
|
ABC1503 International Oil Seal - 1.625" ID, 2.441" OD, 0.312" wide
|
ABC2819 Differential Bearing Retainer Oil Seal - 1.832" O.D. 1.062" I.D. 0.250" width
|
ABC1628 Belt Pulley Output Shaft Seal - Fits Cub and Cub LoBoy
|
IHS1516 Final Drive Gasket Set (for 1 side)
|
IHS1518 Final Drive Pan Gasket
|
IHS645 Rockford Clutch Kit - Woven clutch disc is 6.5" OD with 10 splines and a 15/16" hub.
|
ABC550 New Pressure Plate - 6-1/2" diameter
|
MHS076 Clutch Disc 6 1/2 Inch 10 Spline - 6-1/2" diameter, 15/16" x 10 tooth spline
|
IHS015 Farmall Cub Throwout Bearing - Graphite style bearing like the original.
|
IHS730 Clutch Pilot Bushing - Sintered bronze. 0.815" Outside Diameter, 0.625" Inside diameter, 1.000" Length.
|
836202 Clutch Pilot Bearing - 1.375" OD
|
ABC1437 Clutch Alignment Tool - Plastic, 10 Splines, 15/16" Spline O.D.,0.625 Pilot Diameter
|
IHS1541 Clutch Housing Inspection Cover
|
IHS266 Gear Shift Knob - Can also be used as a reverser knob. 0.375" Hole dia.
|
IHS011 2nd And 3rd Sliding Gear - 17 & 26 Teeth
|
IHS012 Farmall Cub Newer 2nd and 3rd Sliding Gear - 16 & 26 Teeth
|
IHS013 Farmall Cub 1st and Reverse Sliding Gear - 13 Teeth
|
IHS824 Gear Shift Lever - 13" Overall Length
|
IHS3439 Transmission Spline Shaft Oil Seal
|
|
|