Brake, Clutch, Differential, Rear Axle & Transmission
IHS5950 49056DA Transmission (Frame) Cover Gasket - Fits Farmall M, W6, (Supers: M, MTA, W6), 400, 450, 560, 574, 660, 674
|
IHS5744 Pulley Drive Opening Cover Gasket - USA Made
|
IHS5747 Rear Axle Carrier Gasket - USA Made
|
IHS5764 Transmission Driving Shaft Bearing Retaining Gasket - USA Made
|
IHS6380 Gear Spring Lever Spring - USA Made
|
IHS5738 Transmission Countershaft Bushing
|
ABC453 Riveted Brake Disc - 12 Spline6-1/2" Dia2-1/4" Spline ID0.500" thick4 used per tractor
|
MIS1131 Brake Riveting Tool - 1-1/4" throat depth1/8" diameter rivet punch5/16" anvil
|
MIS2547 Deep Throat Brake Rivet Tool - 3-3/8" Deep Throat2-1/8" high throat - USA Made
|
IHS828 Disc Brake Adjusting Bolt - 7/16" - 20 UNF x 4-1/2" - USA Made
|
IHS3067 Brake Pedal Pawl Pin
|
IHS690 Rubber Brake Boot Dust Cover - FOR DISC BRAKES
|
IHS5750 Disc Brake Inspection Cover
|
IHS3070 Brake Lock Assist Attachment - bolts to the lower dash panel
|
IHS823 Disc Brake Actuating Spring - 1.209" overall length, 0.105" wire dia., 0.761" OD
|
ABC1225 Disc Brake Ball - 7/8" Diameter steel ball (0.875")
|
JDS1222 Brake Shaft Oil Seal - 1.125" I.D., 1.832" O.D., .0250" wide
|
ABC3203 Bull Pinion Shaft Bearing Retainer Oil Seal - 2.250 ID, 3.256 OD, 0.375 Wide
|
ABC1565 Rear Axle Seal on International and John Deere - On Case Disc Brake Oil Seal - 2.750" I.D., 3756" O.D., .438 Width
|
COS024 Rear Axle Outer Oil Seal - 3.437" I.D. 4.254" O.D. 0.375" wide
|
ABC3203 Differential Brake Shaft Carrier Seal 2.250 ID, 3.256 OD, 0.375 Wide
|
IHS1371 Clutch and Brake Pedal Shaft - Bare metal --- 24.94" Long, 1.130" Diameter - USA Made
|
IHS4442 Rear Axle Felt Seal - USA Made
|
|
359121K Clutch Kit - 12", Single Stage, Fits International/Farmall 400, 450, 560, McCormick SUPER MTA, SUPER W6
|
405300KA Clutch Kit with Aetna Release Bearing - Fits Super MTA, Super W6, 400, 450, 560, 660, 706, 756, 766, 786, 806, 826, 856, 886, 966, 986 all with 12" 6 Pad Heavy Duty Single Stage
|
ABC2501 Throw-out Bearing - Sealed bearing, no need to grease. 2.490" I.D., 4.060" O.D., 0.870" wide.
|
ABC496 Clutch Throw Out Bearing (IH Torque Amplifier Release Bearing) - 2.062" I.D. 0.801" thick 3.269" face diameter (this is where the pressure plate fingers make contact)
|
ABC2937 Clutch Pilot Bearing - This is a sealed bearing. 0.984" I.D., 2.047" O.D. and is 0.590" wide.
|
IHS2499 Clutch Alignment Tool - Fits Super MTA, 21456, 400, 450, 560, 660, 706, 756, 766, 786, 806, 826, 856, 886, 966, 986, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 3088, 3288, 3688, 4100, 4156, 4166, 4186
|
|
|