Brake, Clutch, Differential, Rear Axle & Transmission
IHS6228 Clutch Joint Rubber Washer, Farmall -Fits A, AV, SUPER A, SUPER A-1, SUPER AV, SUPER AV-1, B, BN, C, SUPER C, 100, 130, 140, 200, 230, 240, 404 USA MADE
|
IHS6269 Right Hand Thread Selective Transmission Shift Turning Joint
|
IHS985 Brake / or Governor Spring - .085" WIRE DIAMETER --- 1.960" OVERALL LENGTH --- .560" DIAMETER
|
IHS493 Round Clutch Inspection Plate - 4-3/16" O.D.
|
IHS627 Clutch Dust Cover (Release Bearing Grease Hole Cover) - 2.025" O.D.
|
ABC426 Riveted Brake Disc - 10 Spline, 5" Diameter 1-5/8" Spline ID .569 thick --- 4 used per tractor---riveted like the originals were!
|
MIS1131 Brake Riveting Tool - 1-1/4" throat depth1/8" diameter rivet punch5/16" anvil
|
MIS2547 Deep Throat Brake Rivet Tool - 3-3/8" Deep Throat2-1/8" high throat - USA Made
|
ABC561 Actuating Spring For Disc Brakes - 0.105 wire diameter 1.275 o/a length; 0.809 o.d.-----4 used per tractor
|
ABC1225 Disc Brake Ball - 7/8" Diameter steel ball (0.875")
|
JDS1222 Brake Shaft Oil Seal - 1.125" I.D., 1.832" O.D., .0250" wide
|
ABC1503 Oil Seal - 1.625" ID, 2.441" OD, 0.312" wide
|
ABC2648 Bull Pinion Shaft Bearing Retainer Seal - 2.754" O.D., 1.750" I.D., 0.500" wide
|
IHS958 New 9 inch Clutch Kit - 9" diameter. 3 levers. 6 springs. Pressure plate fingers are 0.500" width
|
IHS2681 Woven Clutch Disc - 9" O.D., 6 splines, 1-1/4" spline diameter
|
ABC1928 Clutch Throw-out Bearing - 2.060" inside diameter. 3.215" outside diameter. 0.810" thickness. - USA Made
|
IHS1155 Clutch Release Throw-Out Bearing Carrier - For replaceable throw-out bearing Can update older tractors with graphite style (non-turning) bearing
|
IHS3264 Clutch Pilot Bushing - ID: 0.875", OD: 1.125", Length: 0.995" - USA Made
|
IHS3709 Clutch Alignment Tool - 6 spline 1.250" spline O.D. 0.865" pilot O.D. 5.875" overall length
|
ABC3207 Oil Seal - 2.313 ID, 3.256 OD, 0.438"
|
IHS3468 Clutch Release Sleeve Guide, Bushing - 1.470" O.D. 5.067" long 1.280"
|
IHS3665 Clutch Release Yoke - 7-5/8" overall length
|
IHS266 Gear Shift Knob - Can also be used as a reverser knob. 0.375" Hole dia.
|
IHS780 Position Control Handle Knob - 3/8 - 24 fine thread --- Hole diameter: 3/8 NF --- Width: 1.062" --- Height: 0.940"
|
IHS2480 Rubber Gear Shift Boot - 4-3/4" tall
| | |
|
|