Brake, Clutch, Differential, Rear Axle & Transmission
IHS6295 Transmission (Frame) Cover Gasket - Fits Hydro 70 Hydro 86 (544 Farmall Row-Crop ONLY) USA MADE
|
IHS6292 Transmission (Frame) Cover Gasket - Fits Hydro 70, Hydro 86, 544 (Farmall Row-crop ONLY), 656, 664, 666, 686 USA MADE
|
IHS5924 Spring, 182652A1 - USA MADE
|
IHS5726 Gear Shift Poppet Spring, 41058D - USA Made
|
IHS5962 Torque Amplifier Gasket Kit - Fits IH, 330, 340, 460, 544, 656, 664, 686 - USA Made
|
IHS6269 Right Hand Thread Selective Transmission Shift Turning Joint
|
R8446 Brake Seal Kit - Fits IH 544, 656, 664, 666, 686, Hydro 70, Hydro 86
|
IHS5647 Reverse Idler Gear Bushing
|
IHS5738 Transmission Countershaft Bushing
|
ABC1605 Electric Oil/Fuel Pressure Switch
|
ABC434 Bonded Brake Disc - 10 spline6" diameter1-7/8" spline ID0.500" thick4 used per tractor
|
MIS1131 Brake Riveting Tool - 1-1/4" throat depth1/8" diameter rivet punch5/16" anvil
|
MIS2547 Deep Throat Brake Rivet Tool - 3-3/8" Deep Throat2-1/8" high throat - USA Made
|
IHS692 Rubber Brake Boot Dust Cover - FOR DISC BRAKES
|
ABC561 Actuating Spring For Disc Brakes - 0.105 wire diameter 1.275 o/a length; 0.809 o.d.-----4 used per tractor
|
ABC1225 Disc Brake Ball - 7/8" Diameter steel ball (0.875")
|
JDS1222 Brake Shaft Oil Seal - 1.125" I.D., 1.832" O.D., .0250" wide
|
|
IHS687 Brake Pedal Return Spring, Clutch Pedal Return Spring - Overall length: 8-1/8"
|
ABC1565 Rear Axle Seal on International and John Deere - On Case Disc Brake Oil Seal - 2.750" I.D., 3756" O.D., .438 Width
|
IHS3084 Rear Axle Shaft / Bull Pinion Seal - 1.875" I.D., 2.875" O.D., 0.313" wide
|
ABC4696 Bull Pinion Shaft Bearing Cage O-Ring
|
IHS5797 Snap Ring - Fits Cub, Cub Loboy behind PTO shaft bearing, 154 PTO drive pulley retaining ring, 2606, 544, 606, 644 Transmission main shaft pilot bearing snap ring
|
IHS2996 Clutch Kit - 10-1/2" O.D. 1.125" Clutch spline I.D. 1.687" Pressure plate spline I.D. 16 pressure plate splines
|
IHS2993 New Pressure Plate - 10-1/2" O.D. 16 splines 1.687" spline I.D. 1.188" flywheel step
|
IHS2990 New Woven Clutch Disc - 10-1/2" O.D. 10 spline 1-1/8" spline I.D.
|
ABC496 Clutch Throw Out Bearing (IH Torque Amplifier Release Bearing) - 2.062" I.D. 0.801" thick 3.269" face diameter (this is where the pressure plate fingers make contact)
|
ABC2988 Throw-out Bearing Clutch - 2.375" I.D., 3.500" O.D., 0.730" wide
|
ABC2992 Pilot Bearing - Sealed, 0.787" I.D., 2.047" O.D., 0.590" wide
|
ABC3109 Clutch Alignment Tool - Fits 300, 330, 340, 350, 460, 504, 544, 606, 656, 664, 666, 686, 2504, 2544, 2606, 2656, 3514, 3616
|
|
|