Brake, Clutch, Differential, Rear Axle & Transmission
ACS252 Brake Lining Kit - Fits D17 (up to sn 42000), WD, WD45, WD45 (Diesel), 2" wide x 6-1/2" long
|
MIS1131 Brake Riveting Tool - 1-1/4" throat depth1/8" diameter rivet punch5/16" anvil
|
MIS2547 Deep Throat Brake Rivet Tool - 3-3/8" Deep Throat2-1/8" high throat
|
ACS3558 Brake Pin Removal Tool
|
ACS268 Brake Rod Return Spring - 6-5/8" long
|
ACS266 Rear Brake Shoe Return Spring - Fits D17, WD, WD45
|
ACS283 Allis Brake Return and Hydraulic oil control Spring
|
ACS1191 Brake Anchor Shoe Pin- Fits Allis D17, WD, WD45
|
ACS1995 Brake Drum - 2 used per tractor, 1-1/2" bore with keyway2.860" wide7.875" O.D.
|
ACS2678 Brake and Clutch Pedal Shaft - Fits Allis WD, WD45
|
ACS2612 Final Drive Pan Gasket
|
ACS2978 Clutch Kit - 10" diameter, 1-1/4" I.D. - 10 splined clutch hub, 9 spring pressure plate
|
ACS2972 Clutch Kit - 10" diameter, 1-1/4" diameter - 10 splined clutch hub, 6 spring pressure plate, and the pilot bearing has a 0.984" I.D. and a 2.047" O.D
|
ABC2974 Rebuilt Pressure Plate - 10" O.D. and 6 springs
|
ACS2982 Pressure Plates New - 10" O.D. and 9 springs
|
ACS2980 Clutch Disc - 10" O.D., 1-1/4" Spline Diameter - 10 Spline
|
ABC1928 Clutch Throwout Bearing - 2.060" inside diameter. 3.215" outside diameter. 0.810" thickness.
|
ABC2937 Clutch Pilot Bearing - This is a sealed bearing. 0.984" I.D., 2.047" O.D. and is 0.590" wide.
|
ABC3113 Clutch Alignment Tool - 10 spline, 1-1/4" spline O.D., 0.970" O.D. pilot, and is 5-1/2" overall length
|
ACS5323 Transmission Clutch Disc
|
ACS5326 Transmission Clutch Center Disc
|
ACS5329 Transmission Clutch End Plate
|
ABC085 Gear Shift Lever Knob - 3/8" NF - 24 thread, 1.985" Dia., 1.585" Height, 0.325" ID, 1.045" Deep, Bakelite
|
ABC362 Gear Shift Bakelite Knob - 1.250" Diameter 3/8" x 24 NF
|
ACS202 Rubber Knob - 0.400" I.D. hole For ease of installation please lubricate
|
ACS174 Rubber Gear Shift Boot - 1-3/4" bottom ID --- 9/16" hole diameter
|
ACS171 Curved Gear Shift Lever
|
ACS254 Gear Shift Lever Washer And Snap Ring Kit - Retains gear shift lever into housing, 0.254" Thick, 1.368" O.D., 0.998" I.D.
|
ACS253 Oversized Gear Shift Lever Pins
|
ACS255 Standard Gear Shift Lever Pins - 0.314" width for the square end 0.250" shaft diameter
|
|
|