Brake, Clutch, Differential, Rear Axle & Transmission
ABC451 Bonded Brake Disc - 2-1/2" Spline ID, 7" Dia, 29 Spline
|
ABC444 Brake Disc - 8.00" O.D. X 5.00" I. D, 21 Spline Hub, 2.750" Shaft Dia
|
MIS1131 Brake Riveting Tool - 1-1/4" throat depth1/8" diameter rivet punch5/16" anvil
|
MIS2547 Deep Throat Brake Rivet Tool - 3-3/8" Deep Throat2-1/8" high throat - USA Made
|
ABC3477 Actuating Spring (for disc brakes) - 1.294" overall length, 0.110" wire dia., 0.840" O.D. - USA Made
|
IHS823 Disc Brake Actuating Spring - 1.209" overall length, 0.105" wire dia., 0.761" OD
|
ABC1225 Disc Brake Ball - 7/8" Diameter steel ball (0.875")
|
ABC2713 1 inch Disc Brake Ball
|
ABC3209 Brake Shaft Oil Seal - Fits John Deere 820, 830 & 840 (all 2 cylinder) - 1.750" I.D., 2.254" O.D. 0.350" wide
|
ABC196 PTO or Transmission Input Shaft Oil Seals - 2.000" I.D. 2.754" O.D. 0.510" wide
|
ABC3201 Bull Pinion Shaft Bearing Retainer Oil Seal - 2.875" I.D., 3.756" O.D., 0.438" wide
|
W155916K Clutch Kit - 11", Single Stage, Fits Oliver 1550, 1555, 1600
|
W168825K Clutch Kit - 12", Single Stage 6 Pad, Fits Minneapolis Moline G850 & Oliver 1750, 1755
|
W168012K Clutch Kit - 13", Single Stage, Fits Oliver 1750, 1800, 1850, 1855, 1950T, 1955, 2050
|
W168824K Clutch Kit - 12", Single Stage, Fits Minneapolis Moline G750 & Oliver 1650, 1655, White 2-70, 2-78
|
ABC1937 Throw-out Bearing - 2.260" inside diameter. 3.650" outside diameter. 0.800" thickness.
|
ABC496 Clutch Throw Out Bearing (IH Torque Amplifier Release Bearing) - 2.062" I.D. 0.801" thick 3.269" face diameter (this is where the pressure plate fingers make contact)
|
OLS3423 Throw Out Bearing Housing Tube - all without hydra power or creeper drive, 1.675" O.D. 1.550" I.D. 4.705" long
|
8225518 Clutch Release Bearing -3.750" OD
|
ABC3209 Oil Seal - 1.750" I.D., 2.254" O.D. 0.350" wide
|
ABC085 Gear Shift Lever Knob - 3/8" NF - 24 thread, 1.985" Dia., 1.585" Height, 0.325" ID, 1.045" Deep, Bakelite
|
ABC362 Gear Shift Bakelite Knob - 1.250" Diameter 3/8" x 24 NF
|
ACS130 Rubber Gear Shift Boot - 2.25" bottom I.D., 7/16" hole diameter
|
MMS017 Rubber Gear Shift Boot - 1-7/8" BOTTOM I.D. 1/2" HOLE DIAMETER
|
MMS026 Rubber Shift Lever Boot - 2" I.D. bottom hole, 5/8"I.D. top hole
|
ABC387 Transmission Input Shaft Seal - 1.375" I.D., 2.000" O.D., 0.337" wide
|
IHS1307 Trans Drive Shaft / Input Shaft Oil Seal - 1.875" I.D., 2.627" O.D., 0.312" wide
|
ABC2835 Oil Seal - 4.000" I.D., 5.004" O.D., 0.312" wide
|
ABC2069 Oil Seal -2.175" I.D., 3.000" O.D., 0.380" wide
| |
|
|