Brake, Clutch, Differential, Rear Axle & Transmission
|
|
MFS7285 Seal - Rear Axle Differential Carrier Plate
|
MFS2948 2-Piece Brake Shoe Kit - Fits MF F40, TO35, 135, 150, 230, 235, 245, 35, 50, For 13.5" drums
|
MFS2628 Brake Shoe Set - For 13.5" drums
|
ABC3300 Disc Brake Linings With Rivets - outside diameter: 7"
|
MIS1131 Brake Riveting Tool - 1-1/4" throat depth1/8" diameter rivet punch5/16" anvil
|
MIS2547 Deep Throat Brake Rivet Tool - 3-3/8" Deep Throat2-1/8" high throat - USA Made
|
MFS1874 Brake Drum Retaining Screw - Zinc finish. 1/2 -13 NC x 3/4"
|
|
IHS823 Disc Brake Actuating Spring - 1.209" overall length, 0.105" wire dia., 0.761" OD
|
A-180809M1 Spring, Brake Lock
|
ABC1225 Disc Brake Ball - 7/8" Diameter steel ball (0.875")
|
CKS2647 Brake Disc Ball - 211-15 steel brake ball (5/8")
|
ABC3209 Brake Shaft Oil Seal - Fits John Deere 820, 830 & 840 (all 2 cylinder) - 1.750" I.D., 2.254" O.D. 0.350" wide
|
A-180801M1 Bushing, Brake Shaft - 1-3/8" X 1-1/2" X 1-7/16"
|
ABC3362 Belt Pulley Gearbox Seal - 2.125 ID, 2.879 OD, 0.438 Wide
|
183254M1 Differential Plate Gasket - 15-1/4" O.D.
|
MFS4097 Differential Lock Coupling Cap - 10 lugs, 8 mounting holes
|
MFS4106 Differential Lock Coupler - 10 lugs, 39 internal splines
|
MFS2091 Clutch Kit - 11" 10 spline rigid disc, 11" 10 spline double clutch pressure plate, 12 spring pressure plate assembly, 0.485" width across forged finger
|
MFS2311 Clutch Disc - 11" diameter disc & 10 splines
|
ABC2501 Throw-out Bearing - Sealed bearing, no need to grease. 2.490" I.D., 4.060" O.D., 0.870" wide.
|
ABC3149 Clutch Pilot Bearing - ID = 0.669", OD = 1.575", Width = 0.472".
|
MFS4394 Clutch Alignment Tool - USA Made
|
ABC221 PTO Knob Or Gear Shift Knob Or Brake Lever Knob - Plastic, 1.485" OD above band, 1.336" Tall, 1.640" OD below band, 3/8" NFT = .375" x 24 NF, 0.750" Depth
|
ABC085 Gear Shift Lever Knob - 3/8" NF - 24 thread, 1.985" Dia., 1.585" Height, 0.325" ID, 1.045" Deep, Bakelite
|
MFS1965 Gear Shift Boot - 0.510" I.D. top hole, 1.600" I.D. bottom hole
|
MFS158 Spring & Clip For Gear Shift Lever - .800" I.D small end, 1.265" I.D. big end, 1.009" O.D. small end, 1.469" O.D. big end, .103" Wire Dia., 2.133" Overall free length
|
ABC1501 Main Drive Pinion Shaft Seal - 1.125" I.D., 1.565" O.D., 0.250" wide
|
ABC1514 Oil Seal - 0.875" I.D., 1.379" O.D., 0.250" wide
|
|
|