Brake, Clutch, Differential Rear Axle & Transmission
ABC105 Lined Brake Band - 1 band for 1 wheel only, Hinged
|
ABC017 Brake Shoe Lining Set - Long shoe is 2" W x 7-3/8" LShort shoe is 2" W x 6 3/8" L
|
MIS1131 Brake Riveting Tool - 1-1/4" throat depth1/8" diameter rivet punch5/16" anvil
|
MIS2547 Deep Throat Brake Rivet Tool - 3-3/8" Deep Throat2-1/8" high throat
|
ACS271 Brake Shoe Return Spring - 3-1/2" overall length
|
ACS1650 Brake Pivot Pin Toggle Pin - Zinc plated0.750" diameter1.625" longPin is used with hand brakes and foot brakes
|
ACS1652 Brake Adjusting Screw - Zinc plated7/16" - 20 NF3" longOur brake adjusting screw is used on tractors with foot brakes only
|
ACS091 Brake Drum - are made from ductile iron which is far superior to cast iron brake drums
|
|
ABC1562 Rear Axle Oil Seal - 2.500" I.D., 3.548" O.D., .438" Width
|
ACS1529 Oil Seal - Fits Allis B, C, CA, ED40, IB as a Outer Upper Final Drive Shaft Seal - 1.375" I.D., 2.720" O.D., .468" WIDTH
|
ABC1628 Inner Upper Final Drive Shaft Seal - Fits B, C, CA, D14
|
ACS1525 Final Drive Pan Gasket
|
ACS2470 New Clutch Kit - new 9" woven clutch disc w/ 1 1/8"-10 splined hub 9" pressure plate
|
ACS346 New Clutch Kit - 8-1/2" Diameter Pressure Plate 8-1/2" Rigid 10 Spline Clutch Disc
|
IHS2681 Woven Clutch Disc - 9" O.D., 6 splines, 1-1/4" spline diameter
|
ABC496 Clutch Throw Out Bearing - 2.062" I.D. 0.801" thick 3.269" face diameter (this is where the pressure plate fingers make contact)
|
ABC2937 Clutch Pilot Bearing - This is a sealed bearing. 0.984" I.D., 2.047" O.D. and is 0.590" wide.
|
IHS3264 Clutch Pilot Bushing - ID: 0.875", OD: 1.125", Length: 0.995"
|
ACS270 Clutch Return Spring - 4.300" long, 0.750" body diameter, 0.100" wire diameter.
|
ACS305 Clutch Pedal Return Spring - 5.573" overall length, 0.100" wire diameter, 0.750" body diameter
|
ABC221 PTO Knob Or Gear Shift Knob Or Brake Lever Knob - Plastic, 1.485" OD above band, 1.336" Tall, 1.640" OD below band, 3/8" NFT = .375" x 24 NF, 0.750" Depth
|
ACS202 Rubber Knob - 0.400" I.D. hole For ease of installation please lubricate
|
ACS174 Rubber Gear Shift Boot - 1-3/4" bottom ID --- 9/16" hole diameter
|
ACS254 Gear Shift Lever Washer And Snap Ring Kit - Retains gear shift lever into housing, 0.254" Thick, 1.368" O.D., 0.998" I.D.
|
ACS253 Oversized Gear Shift Lever Pins
|
ACS255 Standard Gear Shift Lever Pins - 0.314" width for the square end 0.250" shaft diameter
|
ABC3502 Clutch Disc - 9" O.D., 10 splines, Fits 1-1/8" shaft O.D., solid center
| | |
|
|