Cooling
IHS1993 Radiator Cap - 7 PSI, 2.84" O.D., 2.490" tang to tang length, fits 2.050" neck I.D., Cap reads "tighten, remove slowly"
|
IHS337 Radiator Cap - Non Pressurized Systems, 2.108" tang to tang, 2.806" I.D., 2.886" O.D., .398" tang width, 1.845" inside center dia.
|
IHS384 Radiator Cap With Wing - 2.050" neck I.D., 2.870" O.D., 2.075" inside center dia. 2.50" tang to tang length, .400" tang width, includes gasket
|
IHS925 Winged Radiator Drain Cap - 3/8" pipe thread, has "IH" stamped into it, includes gasket, Cast Iron with ZINC Plating - USA Made
|
IHS443 Radiator - Fits IH Super A, Super AV, Super AV-1, Super C, 100, 130, 140, 200, 230
|
IHS6585 Radiator - Fits Farmall C
|
ABC455 Radiator Mounting Pad - 1/4" thick, 2" square rubber universal radiator mounting pad fits most tractors with bottom stud
|
IHS3884 Radiator Grill Fastener Screw - Exact as original
|
R4160 Radiator Mounting Kit
|
IHS142 Fan Assembly - Fits models listed w/o water pump - 15 1/2" Overall fan diameter, 4" Fan pulley Dia., 3 5/8" Generator Pulley Dia.
|
IHS6278 O.E.M. Fan Blade - USA Made
|
IHS5660 Upper Radiator Hose - Fits Super A, Super C, 100, 130, 200 and 230
|
IHS5681 Upper Radiator Hose - Fits Farmall C
|
IHS5684 Lower Radiator Hose - Fits Farmall C
|
IHS6929 Radiator Hose Kit
|
ABC052 Thermostat, 160 Degree (included gasket fits Ford models only) - 160 degree low temperature
|
IHS4461 Water Outlet Elbow Gasket - A, Super A, B, C, Super C, 100, 130, 140, 200, 230, 240, 330, 340, 404, 424, 444, 504
|
IHS6696 Thermostat Spacer - USA Made
|
IHS217 Water Pump - New, includes mounting gasket & pulley
|
IHS2081 Farmall Fan Drive Pulley Assembly - Fits models listed with Water Pump - 3.125 C.C. Fan Bolts, 12-24 UNC Fan Screws, 4.379" OD Rear Pulley, 4.062" OD Front Pulley
|
IHS5616 Water Pump Gasket Kit
|
ABC101 Fan Belt International/Farmall A, B, C Super A - all with out water pump - 11/16" x 32-1/4"
|
ABC102 Fan & Generator Belt - Fits IH models listed with Water Pump (11/16" x 34-1/4")
|
IHS536 Radiator and Fuel Tank Mounting Pad - 1.5" O.D.
|
IHS638 Wittek Tower Clamp - fits hoses measuring between 1.815" and 2.000"
|
IHS639 Wittek Tower Clamp - fits hoses measuring between 1.807" and 2.285" - USA Made
|
IHS640 2 11/16" - 2 1/2" Wittek Tower Clamp (Hose Clamp) - USA Made
|
IHS636 3/4" - 1" Wittek Tower Clamp (Hose Clamp) - Fits hoses measuring .775" and 1.013" - USA Made
|
IHS642 Wittek Tower Clamp - fits hoses measuring between 2.350" and 2.765"
|
IHS643 Wittek Tower Clamp - fits hoses measuring between 2.685" and 2.995"
|
|
|