ACS6832 Turn Signal Switch Knob with Hardware
|
ABC016 Ammeter (Amp) Gauge (20-0-20) - Fits 2" diameter hole, Threaded Terminal Type
|
ABC2238 Ammeter Gauge (60-0-60)
|
ABC109 Ammeter (Amp) Gauge (30-0-30) - Fits 2" diameter hole, Threaded Terminal Type
|
ABC466 Ammeter (Amp) Gauge 60-0-60 - Fits most tractors equipped with alternator, Fits 2" Diameter hole, Threaded Terminal Type
|
CKS076 Ammeter Gauge - Fits 2" Hole
|
ABC082 Universal Oil Pressure Gauge - Dash mounted gauge, requires a 2" diameter hole, 1/8" NPT Male Threads
|
ABC005 Universal Oil Pressure Gauge - Dash mounted gauge, requires a 2" diameter hole, 1/8" NPT Male Threads
|
CKS075 Oil Pressure Gauge - 1/8" male pipe threads
|
CKS1642 Oil Pressure Gauge (0-30 PSI) - with 1/8" male pipe threads, for a 2" Hole
|
ABC2360 Oil Gauge Adapter Fitting - For Gauges Without Removable Fitting---1/8" pipe female to 3/16" tubing female---
|
ABC2353 Oil Gauge Adapter Fitting - 1/8" female to 1/4" Female - Fits 1/4" inverted flare
|
ABC538 Oil Gauge Fitting - For gauges without removable fitting
|
IHS626 Oil Gauge Fitting - For gauges without removable fitting 1/8" pipe to 1/4" compression
|
ABC523 Oil Pressure Gauge Copper Line Kit
|
ABC1593 Water Temperature Gauge - Dash mounted, not illuminated, 2" dia., 60" lead, 5/8"-18 U.F. end w/ 1/2" NPT pipe bushing, Probe dia. 0.374", length is 1-3/16"
|
ABC239 Water Temperature Gauge - Dash mounted, 110 degrees to 230 degrees, Includes 72" long heavy duty capillary tube, 5/8" - 18 UF thread with 1/2" NPT pipe bushing,
|
MFS133 Tachometer Cable - 38 7/8" long with a metal sheath, Square ends, 5/8 - 18 x 7/8 - 18 threads
|
ABC476 Tachometer Drive Assembly - Drives off of the rear of the generator. Includes 14 and 43 tooth gears
|
FDS423 Steel Tachometer Cable - steel outer covering and has a 48" long cable w/ square ends
|
ACS2809 Tachometer Drive Gear and Shaft - 12 Teeth
|
ACS2803 Tachometer Drive Assembly - 12 Teeth on Drive Gear, 45 Teeth on Driven Gear
|
MFS140 Starter Switch This switch measures 1" from the top of the mounting plate to the end of the button. The measurement between bolt holes (center to center) is 1-3/4".
|
|
ABC2285 Electrical Outlet Socket Boot - Fits tractors using single wire outlet
|
CKS112 Restoration Quality Wiring Harness - For 6 volt generator systems with a cut-out relay only, includes light wires & instructions
|
CKS2875 Restoration Quality Wiring Harness -using Autolite gauge panel and original 12-volt generator (not for Stewart Warner gauge panel), includes light wires & instructions
|
ABC395 Electrical Outlet Socket 2 plated brass pins, All implements with lights
|
ABC1868 Auxiliary Male 2-PIn Connector Plug - Plated brass pins, 0.760" wide, 3.045" total length and 0.340" hole diameter for wires
|
MIS3127 Auxiliary Heater - USA Made
|