Hitch and Hydraulics
JDS5480 Hydraulic Selective Control Valve
|
JDS5741 Hydraulic Pump 50CC
|
JDS6016 Drawbar Support - Fits John Deere 4000, 4020, 4040, 4230, 4240, 4320, 4430, 4440, 4455
|
JDS5094 Hydraulic Filter Element
|
|
JDS6318 Hydraulic Pump Repair Kit
|
JDS6321 Hydraulic Pump Repair Kit - USA Made
|
JDS6324 Hydraulic Pump Repair Kit
|
R3144 Right Hand Sway Block
|
ABC209 Block & Hydraulic Drain Plug - 1/4" - 18 NPT
|
|
|
JDS4689 Hydraulic Pump 50CC
|
|
|
AR56160 Pump, Hydraulic Assembly - Fits JD 2130, 3030, 3130, 4020 (SN <200999), 4040, 4240, 4440, 7/8" Discharge, 50 cm. 3.0ci
|
AR94661 Pump, Hydraulic Assembly - Fits John Deere 4000, 4020, 4040, 4230, 4240, 4320, 4430, 4440, 4520, 4620, 4630, 4640, 4560, 4650, 4755, 4760, 4850, 4955, 4960, 4830, 8440, 8450, 8630 -Remanufactured 1-1/16" Front Discharge
|
AR94660 Pump, Hydraulic Assembly - Fits JD 3010, 3020, 4000, 4010, 4020, 4040, 4050, 4055, 4230, 4240, 4250, 4255, 4320, 4350, 4430, 4440, 4450, 4455, 4520, 4620, 4630, 4640, 4840, 5010, 5020, 6030, - 50 cm, 1 1/16" Discharge Port, 1 1/16" Inlet Ports
|
JDS1496 Hydraulic Pump Drive Bushing - 1.070" O.D., 0.565" I.D., 0.657" Long, Black rubber
|
JDS3861 Front Hydraulic Pump Drive Clamp Half - 5.142" overall length 2" wide (1) 3/8"-16 NC threaded hole
|
ABC532 Toplink Ball Category 2 - 1.988" outside (nominal) diameter 1.015" hole diameter 1.374" diameter of flat 2.008" width 48 - 55 Rockwell 4142 steel zinc plated
|
ABC530 Toplink Ball Category 1 - 1.988" outside (nominal) diameter, 0.765" hole diameter, 1.310" diameter of flat, 1.720" width, steel zinc plated
|
AR34209 Link, Top Category II - Center Link, 1" Pin
|
RE44558 Link, Top, Category III - Center Link, 1-1/4" Pin
|
JDS012 Right Hand Sway Block
|
JDS013 Left Hand Sway Block
|
R61184 Drawbar, Rear Curved - Fits John Deere 4055, 4255, 4050, 4055, 4240, 4240S, 4250, 4255, 4350, 4440, 4450, 4455, (45.625" Long, 3" Wide, 1.5" High, 2" Bend)
|
R62081 Drawbar, Rear Curved - Fits JD 4555, 4560, 4640, 4650, 4755, 4760, 4840, 4850, 4955, 4960, 45.625" Long, 3" Wide, 1.5" High, 2" Bend
|
R80842 Drawbar, Rear Curved - Fits John Deere 4000, 4020, 4030, 4040, 4230, 4320, 4430, (45" Long, 2.5" Wide, 1.375" High)
|
JDS1796 Center link Handle
|
|
|