MHSK1 Deck Stabilizer Kit
|
IHS5737 Hydraulic Oil Reservoir Gasket - USA Made
|
IHS5740 Hydraulic Manifold Gasket - USA Made
|
IHS6508 Farmall Cork Implement Bolt Hole Plug Kit
|
IHS5575 Hydraulic Pump Gasket
|
ABC4698 Pesco Hydraulic Pump Rear Oil Seal
|
ABC3910 Rope Trip Plow Clip - Mounts to existing seat pan bolt or on earlier tractors it mounts to existing seat pivot pin
|
IHS097 Bolster Pivot Pin - 1-1/4" diameter, 8-1/2"long, Rowcrops only (will not fit standards/wheatlands)
|
IHS278 Live Hydraulic Pump - 3-7/8" flange to flange - Fits gas & LP only
|
IHS1240 Hydraulic Pump Flange - 3/4" NPT inlet and outlet --- threaded for hydraulic hose
|
IHS1237 Hydraulic Pump Flange - 3/4" NPT --- Threaded for hydraulic hose
|
IHS3089 Hydraulic Belly Pump Filler Pipe & Control Rod Dust Seal Spring - 1.480" Length ** 1.125" I.D. ** 0.065" wire thickness
|
IHS3653 Thompson Hydraulic Pump Seal, O-Ring and Gasket Set - 13-piece kit Note: Fits pump #'s 363779R91, 363779R92, 363779R93, 363779R94, 366823R91, 366823R92, 366823R93
|
IHS3095 Hydraulic Belly Pump Oil Outlet Elbow Dust Seal Spring - 1.060" O.D. ** 1.475" Length ** 0.065" wire thickness
|
IHS3100 Hydraulic Belly Pump Filler Pipe & Control Rod Metal Washer - 2" O.D. x 1" O.D. hole x 0.062" thick
|
IHS3091 Hydraulic Belly Pump Filler Pipe & Control Rod Felt Washer - 2" O.D. ** 1" I.D. ** 0.125" Thick
|
IHS3104 Hydraulic Belly Pump Oil Outlet Elbow Metal Washer - 2" O.D. x 7/8" I.D. hole x 0.062" thick
|
IHS3068 Hydraulic Pump Control Rod - 38" long and the O.D is 3/8"
|
IHS366 Lift All Control Rod Spring / Flat Hold-Down Spring - For Hydraulic Pump Lift Lever
|
IHS3098 Hydraulic Belly Pump Oil Outlet Elbow Felt Washer - 2" O.D. ** 0.750" I.D. ** 0.125" Thick
|
IHS1440 Farmall H and M Hydraulic Dipstick - Mounts inside the hydraulic pump breather fill pipe. --- 11.800" Long
|
IHS3473 Hydraulic Cylinder Seal Kit - with remote 3-1/2" x 8" hydraulic cylinder attachment - USA Made
|
MIS4560 Hitch Pin 7/8" x 6-1/2"
|
MIS4555 Hitch Pin 3/4" x 6-1/2"
|
MIS4563 Hitch Pin 1" x 7-1/2"
|
ABC1433 Lift Arm / Top Link Reducer Bushing - For tractors with Category 2 3 PT hitch switching to category 1 3PT. ***7/8" ID --- 1-1/8" OD --- 1-3/8" overall Length***
|
ABC4185 Top Link Reducer Bushing, Category 2 to Category 1 - 0.750" I.D., 1.000" O.D., 1-15/16" length
|
IHS3009 International 3 Point Hitch Conversion - Fits Rowcrops and Utilities without fast hitch. It also allows use of original draw bar
|
IHS1377 Front Drawbar Pin - The length of this pin is 3 7/16"
|
IHS910 Straight Swinging Drawbar - 53-1/4" overall length. This drawbar is 3/4" thick and 2-1/4" wide. There is an oval hole in the end where the pin goes thru like the original straight swinging drawbar
|