Hitch and Hydraulics
MHSK1 Deck Stabilizer Kit
|
IHS5858 Flow Control Valve Ball Spring - Fits Super A, C, Super C, Cub, 200, 230, 240, 300, 330, 340, 350, 354, 365, 384, 400, 424, 444, 450, 460, 560, 660 - USA Made
|
|
IHS6735 Hydraulic Filter Extension Kit - USA Made
|
IHS5575 Hydraulic Pump Gasket
|
ABC4698 Pesco Hydraulic Pump Rear Oil Seal
|
IHS097 Bolster Pivot Pin - 1-1/4" diameter, 8-1/2"long, Rowcrops only (will not fit standards/wheatlands)
|
ABC4550 Hydraulic Filter - fits tractors listed with C135, C153, C200, C221, C263, C291, D166, D188, D236, D239, D282, D312 Engines
|
IHS5058 IHC 2-1/2" X 8" Cylinder O-Ring and Seal Kit
|
IHS278 Live Hydraulic Pump - 3-7/8" flange to flange - Fits gas & LP only
|
IHS5602 Hydraulic Level Friction Spring
|
IHS3520 Thompson Hydraulic Pump Gasket, O-Ring and Seal Kit - For pumps rated at 9 gpm (gallons per minute), 11 piece kit. - USA Made
|
IHS1924 Hydraulic Pump Gear - 16 Teeth, Gas, w/ 9 GPM side engine mounted pump
|
IHS1237 Hydraulic Pump Flange - 3/4" NPT --- Threaded for hydraulic hose
|
IHS3653 Thompson Hydraulic Pump Seal, O-Ring and Gasket Set - 13-piece kit Note: Fits pump #'s 363779R91, 363779R92, 363779R93, 363779R94, 366823R91, 366823R92, 366823R93
|
IHS3525 Pesco Hydraulic Pump Gasket, O-Ring and Seal Kit - Repairs Pesco pump # 368894R91. 9 piece kit
|
IHS3506 Pesco Hydraulic Pump Gasket, O-Ring and Seal Kit - Verify pump # before ordering as there were different pumps used by IHC - USA Made
|
IHS4243 Hydraulic Pump Mounting Gasket & O-Ring Kit - USA MADE
|
IHS117B 3 Pt Fast Hitch Prongs Category 2 - Fits International 300, 350, 340, 400, 450, 560, 606, 656, 706, 756, 806, 856, 966, 1206, 1256
|
IHS3473 Hydraulic Cylinder Seal Kit - with remote 3-1/2" x 8" hydraulic cylinder attachment - USA Made
|
IHS3537 Touch Control Hydraulic Strainer With Gasket - 8.235" overall length 2.400" screen OD
|
ABC2010 Category 1 Adjustable Stabilizer Bar - Adjustable ends for desired length, adjust from 27-1/2" to 37" length. 23" center tube length. 7/8" threaded ends. 7/8" pin holes
|
FDS023 Top Link - Category 1, 16" long tube, 3/4" holes at both ends
|
FDS022 3 Point Drawbar - Category 1, black primer, measures 1" x 2-1/2" x 26", (approximately 31-1/2" overall length, pin to pin) with a 7/8" pin size
|
IHS3077 Fast Hitch Pin with Ball and Handle - 3/4" O.D. and the length is 4-1/2" long (pin only).
|
MIS4560 Hitch Pin 7/8" x 6-1/2"
|
MIS4555 Hitch Pin 3/4" x 6-1/2"
|
MIS4563 Hitch Pin 1" x 7-1/2"
|
IHS3069 Fast Hitch Pin with Ball - 3/4" O.D. and is 2-7/8" long
|
ABC1433 Lift Arm / Top Link Reducer Bushing - For tractors with Category 2 3 PT hitch switching to category 1 3PT. ***7/8" ID --- 1-1/8" OD --- 1-3/8" overall Length***
|
|
|