FDS073 Friction Disc - 3" OD, 1/2" CENTER HOLE, 0.210" thick material
|
MFS3751 Main Hydraulic Pump Assembly - Using 10 spline, 1-3/8" diameter camshaft and 0.091" pistons and strainer, 2300-2800 PSI, 7-3/4" width 5-1/2" height 12-1/2" overall length
|
ABC266 Hydraulic Lift Piston Ring Kit - For applications using 2 1/2" diameter lift piston
|
MFS3948 Single Hydraulic Remote Valve With Lever - This valve bolts to the lift cover. Outlets are 1/2" pipe thread
|
MFS3633 Dual Hydraulic Remote Valve Kit
|
MFS5625 Hydraulic Control Valve
|
ABC300 Hydraulic Lift Piston - using 2 1/2" diameter lift piston
|
ABC314 Hydraulic Lift Piston - using 2 1/2" diameter lift piston
|
ABC316 Hydraulic Lift Piston Washer - This back up washer installs BEHIND the O-RING. For 2 1/2" diameter lift piston.
|
ABC315 Hydraulic Lift Piston O-Ring - This O-Ring installs toward head of the lift cylinder piston, for 2 1/2" lift cylinder piston. 2.100" I.D., 2.500" O.D., 0.210" thick
|
MFS3554 Hydraulic Lift Cover Valve Block Off Plate - 3.775" overall length 2.950" wide (1) 1/8" NPT port
|
MFS4356 Hydraulic Lift Piston
|
MFS4359 Hydraulic Lift Piston Ring Kit - Ford 3" Pistons, includes 3 Rings
|
MFS3614 Hydraulic Lift Cover Gasket - 0.017" thick
|
MFS128 Hydraulic Oil Level Indicator / Dip Stick - All Gas/Lp & Dsl For Hydraulic Oil Level, Mounts On Side Cover Of Rear End Housing
|
ABC4319 Single Hydraulic Remote Hose, Coupler, and Bracket Kit
|
GG100 - Hydraulic Pressure Testing Gauge - 100 lbs.
|
GG300 - Hydraulic Pressure Testing Gauge - 300 lbs.
|
GG400 - Hydraulic Pressure Testing Gauge - 400 lbs.
|
GG600 - Hydraulic Pressure Testing Gauge - 600 lbs.
|
GG1500 - Hydraulic Pressure Testing Gauge - 1500 lbs.
|
GG2000 - Hydraulic Pressure Testing Gauge - 2000 lbs.
|
GG3000 - Hydraulic Pressure Testing Gauge - 3000 lbs.
|
GG5000 - Hydraulic Pressure Testing Gauge - 5000 lbs.
|
ABC435 Drawbar Clevis With Pin - Will not fit 2000 except Rowcrop and 4000 except Rowcrop and Grove
|
FDS022 3 Point Drawbar - Category 1, black primer, measures 1" x 2-1/2" x 26", (approximately 31-1/2" overall length, pin to pin) with a 7/8" pin size
|
FDS208 Swinging Drawbar Assembly - If planning to install on early Ford tractors, please verify that there are 4 tapped holes under your rear end housing
|
FDS306 Swinging Drawbar - 29-5/8" overall length 1" thick 2" wide Pin hole is approximately 0.945"
|
ABC2271 Swinging Drawbar Bolt Kit - Includes 8 bolts and lock washers. 4 bolts 7/16 - 14 x 1 1/2" long and 4 bolts 5/8 - 11 x 1 1/2" long.
|
FDS211 Drawbar Lock - Category 1 - Keeps 3-Point hitch drawbar from twisting
|