ABC310 Ignition Tune-Up Kit With Rotor - only fits Autolite distributors with 3-3/8" OD cap, Will not fit models IGZ or IGW distributors
|
EIGN28 Electronic Ignition Kit - 12 Volt Negative Ground
|
ABC518 Autolite Rotor Button - Fits AUTOLITE Distributors With 3 3/8" O.D. Clip Held Cap---Will not fit IGZ or IGW distributors
|
ABC137 Distributor Cap - This is for Autolite distributors with CLIP held cap. Will not Fit IGW or IGZ distributors
|
ABC4235 Distributor Dust Cover with Felt Seal - fits Autolite distributors only with 3-3/8" O.D. caps
|
|
ABC348 Vertical Hot Coil 12 Volt Externally Resisted 55000 - Delco distributors WITH SCREW HELD CAP --- Kit contains: Heavy duty point set vibration resistant condenser and rotor
|
ABC509 12V Coil Internal Resisted - Barrel style Internally resisted Includes coil mounting bracket
|
R3528 12 Volt Flame Thrower Coil - for all 12 volt systems requiring horizontal mounting position - Internally Resisted 3 OHMS.
|
ABC366 2 Terminal Style Universal 12-volt Voltage - 2 terminal style Reduces voltage to distributor points 2.0 OHMS of resistance, Limits voltage to coil when using 12-volt battery.
|
ABC324 Autolite Spark Plug - 18 MM thread diameter 1/2" reach 7/8" Hex Medium hot Power tip/non resistor
|
ACS228 Spark Plug Wire Set - Dimensions= (approximately) 2 wires= 32", 1 wire= 34 1/2", 1 wire = 38", & coil wire = 24" The coil wire is made from excess wire left over from the spark plug wire.
|
FDS149 Spark Plug Wiring Set 4 Cylinder - This spark plug wires set fits most 4 cylinder models. They have copper core wires with aluminum coating to prevent corrosion. And 90 degree boots.
|
MFS105 Spark Plug Wiring Set - These wires have a copper core with aluminum coating to prevent corrosion. --- PREMIUM QUALITY --- NO CUTTING OR FITTING REQUIRED ***
|
ABC4291 Spark Plug Wiring Set with Straight Boots, 4-cyl. - Use with electronic ignitions
|
ABC4309 Spark Plug Wiring Set for Electronic Ignition with 90 degree Boots -
|
ABC4340 Spark Plug Wiring Set (Pre-assembled) with Straight Boots, 4-cyl. - For Tractors with Electronic Ignition
|
MAG6 Wico XH And XHD Magneto Service
|
KEY1094 Ignition Key (OEM) Verify key style before ordering, as more than one style could be used
|
ABC400 Ignition Key Switch - For battery ignition only, 3/4" Dia thread, 4 terminals --- 4 position switch, has 4 stud terminals --- Includes 2 keys
|
CKS111 Ignition Key Switch With Keys This switch has 3 posts with 4 screw type terminals and includes 2 keys The threaded stem measures 9/16 - 24 UNEF
|
CKS113 Ignition Switch With Keys This switch has 4 spades with 5 screw type terminals. It is a 4 position switch. Two keys are included. The threaded stem measures 9/16 - 24 UNEF
|
ABC398 Universal 2 Position Push Pull Ignition and Light Switch The knob measures 10-24 NC thread pitch. The threaded stem measures 3/8 - 24 UNF.
|
ABC489 Magneto Push Pull Switch This switch has 1 screw type terminal. This switch will fit most models with a magneto ignition. The threaded stem measures 3/8 - 32 UNEF.
|