ABC018 - Delco Clip Held Ignition Kit - For use on tractors using Delco-Remy distributors with clip held cap through 1963 Delco Distributors Only
|
IHS370 Horizontal Distributor Ignition Tune Up Kit - This will NOT fit any magnetos or Delco or PrestoLite brand distributors. Plug Gap = .025, Point Gap = .020
|
IHS846 IH Ignition Tune Up Kit - For 4 cyl. models using IH HORIZONTAL distributor number 353898R11 or (VERTICAL distributor 560 Only) number with 367839R92 or 371579R92 . It will not fit Delco or Prestolite distributors.
|
IHS4821 F4 Magneto Cap Brush Set
|
EIGN01 Electronic Ignition Kit, 6 Volt positive ground
|
EIGN19 Electronic Ignition Conversion Kit - 12 volt Negative Ground System 4 cyl Delco distributor with clips
|
EIGN17 Electronic Ignition Conversion Kit - 12 Volt Negative Ground for 4 cylinder IH distributor with clips
|
ABC520 Delco Rotor Button - Tractors using Delco-Remy distributors with clip held cap through 1963
|
IHS703 Rotor Button - This rotor button will fit the IH Horizontal Distributor 353898R11
|
ABC121 Distributor Cap - Fits 353898R11 IH horizontal distributor, Also fits Cub with J4 magneto
|
ABC186 Distributor Dust Cover With Felt Gasket And Washer - Fits tractors using Delco-Remy distributors with clip held cap thru 1963
|
ABC276 Distributor Cap - Fit tractors using Delco-Remy distributors with clip held cap through 1963.
|
IHS763 IH Distributor Dust Cover - this cannot be used on Cub models that have a J4 magneto. Will also fit distributor # 368051R1 & 401107R1.
|
ABC488L Spring Clip And Longer Bracket - Distributor caps use one each of ABC488L & ABC488S FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC488S Spring Clip And Shorter Bracket - Distributor caps use one each of ABC488L & ABC488S - FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
IHS1716 Distributor, Horizontal - CAST STEEL HOUSING LIKE ORIGINAL!
|
IHS815 Distributor Drive Shaft - This is NOT the shaft that the points contact or the weights attach to,This IS the shaft that will fall out of the distributor if removed from the tractor
|
ABC2523 Distributor Hold Down Clamp - For 3/8" hold down bolt. 2 used per engine, sold individually.
|
IHS3112 Distributor Drive Housing - USE TO CHANGE OVER FROM A MAGNETO, OR TO ADD A TACHOMETER DRIVE TO YOUR TRACTOR. The tachometer drive parts or tach drive blockoff plate are sold separately.
|
ABC4181 Distributor Drive Housing Bushing - 0.630" I.D., 0.750" O.D., 0.970" long
|
IHS3125 Distributor Tachometer Drive Housing Block Off Plate w/ Gasket - Used to cover tach drive opening when not equipped with tachometer.
|
ABC3007 Delco Distributor Shaft Bushing and Shim Kit - has an 0.486" I.D., 0.656" O.D. and 2.867" length. Bushing must be sized to shaft after installation
|
IHS3166 IH Distributor Shaft Bushing and Shim Kit - This is a 5-piece kit. The length is 2.006".
|
IHS974 Insulator - This spring anchor terminal insulator is designed for the IH distributor (353898R11) and for J4 magnetos with a serial number higher than 139748.
|
IHS988 Terminal Screw - This product is a zinc plated Terminal Screw only
|
IHS737 Distributor Cap Spring Clip Bracket Screw With Lock Washer - SCREW SIZE: 8-32 X 3/8" SLT RD, HD MACHINE
|
ABC498 Delco Distributor Terminal Insulator Assembly - Fits distributor housings with 0.345" diameter round hole, Will not fit IH built distributors / magnetos
|
ABC500 Delco Distributor Terminal Insulator - Square was the late style that fit distributor housings with .300 Dia hole with a keyway, WILL NOT FIT IH BUILT DISTRIBUTORS/MAGNETOS
|
ABC011 6 Volt Distributor Coil - Metal housing, mounting bracket included-- fits tractors with barrel-type coil
|
|