EIGN199 Electronic Ignition II Conversion Kit, 12 Volt Negative Ground 4 Cyl Delco Distributor with clip mounted cap - USA Made
|
ABC6411 Flame-Thrower II Ignition Coil - USA Made
|
ABC018 Premium Delco Ignition Tune-Up Kit with Rotor - For use on tractors using Delco-Remy distributors with clip held cap through 1963 Delco Distributors Only
|
ACS110 Ignition Tune Up Kit - FITS DELCO DISTRIBUTOR ONLY, Except Delco distributor 1112688 - contains: Spark plugs (with 3/8" reach), heavy duty points, condenser, rotor - - Check!! Spark Plug Gap = .030, Point Gap = .020, Fits 4 cyl Gas engines
|
ABC3978 Ignition Points Only (for Delco Distributor with Clip Held Cap) - For tractors using Delco-Remy distributors only
|
ABC168 Autolite Spark Plug - 14 mm thread diameter 3/8" reach 13/16" hex Medium hot Standard tip/non resistor
|
EIGN19 Electronic Ignition Conversion Kit - 12 volt Negative Ground System 4 cyl Delco distributor with clips - USA MADE
|
ABC276 Distributor Cap - Fit tractors using Delco-Remy distributors with clip held cap through 1963.
|
ABC186 Distributor Dust Cover With Felt Gasket And Washer - Fits tractors using Delco-Remy distributors with clip held cap thru 1963
|
|
ABC488L Spring Clip And Longer Bracket - Distributor caps use one each of ABC488L & ABC488S FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC488S Spring Clip And Shorter Bracket - Distributor caps use one each of ABC488L & ABC488S - FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC3007 Delco Distributor Shaft Bushing and Shim Kit - has an 0.486" I.D., 0.656" O.D. and 2.867" length. Bushing must be sized to shaft after installation
|
ABC498 Delco Distributor Terminal Insulator Assembly - Fits distributor housings with 0.345" diameter round hole, Will not fit IH built distributors / magnetos
|
ABC011 6 Volt Distributor Coil - Metal housing, mounting bracket included-- fits tractors with barrel-type coil
|
ABC348 12 Volt Distributor 'HOT' Coil (55000 Volts)
|
ABC4293 6 Volt Flame Thrower Coil - Use with electronic ignition kits or breaker point ignitions Note: Do not use an external resistor on 6 volt electrical systems
|
ABC6158 12 Volt Distributor 'HOT' Coil (55000-Volts)
|
R3528 12 Volt Flame Thrower Coil - for all 12 volt systems requiring horizontal mounting position - Internally Resisted 3 OHMS.
|
ABC366 2 Terminal Style Universal 12-volt Voltage - 2 terminal style Reduces voltage to distributor points 2.0 OHMS of resistance, Limits voltage to coil when using 12-volt battery.
|
ACS228 Spark Plug Wire Set - Dimensions= (approximately) 2 wires= 32", 1 wire= 34 1/2", 1 wire = 38", & coil wire = 24" The coil wire is made from excess wire left over from the spark plug wire.
|
FDS149 Spark Plug Wiring Set 4 Cylinder - This spark plug wires set fits most 4 cylinder models. They have copper core wires with aluminum coating to prevent corrosion. And 90 degree boots.
|
ABC4291 Spark Plug Wiring Set with Straight Boots, 4-cyl. - Use with electronic ignitions
|
FM02 Fairbanks Morse End Cap Only This is just the end cap that the wires plug into, it does not include the spacer cap between the end cap & the magneto.
|
FM01 Fairbanks Morse Condenser
|
MAG6 Wico XH And XHD Magneto Service
|
|
| | |