ABC018 - Delco Clip Held Ignition Kit - For use on tractors using Delco-Remy distributors with clip held cap through 1963 Delco Distributors Only
|
ABC555 Ignition Tune-Up Kit - Fits Delco Distributor w/ clip held cap Works ONLY on listed 6 cylinder models, Spark Plug thread size is 18 MM diameter 1/2" Reach and 7/8" Hex Replaces Champion D16 & D21 Spark Plug GAP = .025, Point Gap = .020
|
ABC3978 Ignition Points Only (for Delco Distributor with Clip Held Cap) - For tractors using Delco-Remy distributors only
|
ABC170 Autolite Spark Plug - 18 mm thread diameter 1/2" reach 7/8" hex Medium hot Std Tip / Resistor Plug gap 0.025"
|
ABC171 Autolite Spark Plug - 18mm thread diameter 1/2" reach 7/8" hex Hot heat range Std Tip / Resistor
|
R8119 Distributor w/ Tach Drive - NEW
|
ABC520 Delco Rotor Button - Tractors using Delco-Remy distributors with clip held cap through 1963
|
ABC330 Distributor Cap This fits 6 cylinder models using a Early Delco Remy Distributor with a clip held cap #824735
|
ABC186 Distributor Dust Cover With Felt Gasket And Washer - Fits tractors using Delco-Remy distributors with clip held cap thru 1963
|
|
ABC488L Spring Clip And Longer Bracket - Distributor caps use one each of ABC488L & ABC488S FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC488S Spring Clip And Shorter Bracket - Distributor caps use one each of ABC488L & ABC488S - FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC2523 Distributor Hold Down Clamp - For 3/8" hold down bolt. 2 used per engine, sold individually.
|
ABC3007 Delco Distributor Shaft Bushing and Shim Kit - has an 0.486" I.D., 0.656" O.D. and 2.867" length. Bushing must be sized to shaft after installation
|
ABC498 Delco Distributor Terminal Insulator Assembly - Fits distributor housings with 0.345" diameter round hole, Will not fit IH built distributors / magnetos
|
ABC500 Delco Distributor Terminal Insulator - Square was the late style that fit distributor housings with .300 Dia hole with a keyway, WILL NOT FIT IH BUILT DISTRIBUTORS/MAGNETOS
|
ABC011 6 Volt Distributor Coil - Metal housing, mounting bracket included-- fits tractors with barrel-type coil
|
|
ABC348 Vertical Hot Coil 12 Volt Externally Resisted 55000 - Delco distributors WITH SCREW HELD CAP --- Kit contains: Heavy duty point set vibration resistant condenser and rotor
|
ABC4293 6 Volt Flame Thrower Coil - Use with electronic ignition kits or breaker point ignitions Note: Do not use an external resistor on 6 volt electrical systems
|
ABC509 12V Coil Internal Resisted - Barrel style Internally resisted Includes coil mounting bracket
|
R3528 12 Volt Flame Thrower Coil - for all 12 volt systems requiring horizontal mounting position - Internally Resisted 3 OHMS.
|
ABC366 2 Terminal Style Universal 12-volt Voltage - 2 terminal style Reduces voltage to distributor points 2.0 OHMS of resistance, Limits voltage to coil when using 12-volt battery.
|
ABC2863 Spark Plug Wire Set - This wiring set is cut to length, has waterproof neoprene, has 7 mm "tinned" copper core, and includes the coil wire
|
ABC326 Spark Plug Wire Set 6 Cylinder - Copper Core. 35" long waterproof neoprene w/ 90 degree boots. You will have to cut the wires to your desired length & Crimp End W/ A Crimping Tool.
|
ABC5841 Spark Plug Wiring Set w/ Straight Boots, 6 cyl.
|
ABC4296 Spark Plug Wiring Set with Straight Boots, 6-cyl.
|
ABC4300 Spark Plug Wiring Set with 90 degree Boots, 6-cyl.
|
MAG6 Wico XH And XHD Magneto Service
|
KEY01 Ignition Key Verify key style before ordering, as more than one style could be used
|