ABC018 - Delco Clip Held Ignition Kit - For use on tractors using Delco-Remy distributors with clip held cap through 1963 Delco Distributors Only
|
ABC4408 Ignition Tune Up Kit without Rotor - For Delco Distributors listed with Screw Held Caps
|
ABC3978 Ignition Points Only (for Delco Distributor with Clip Held Cap) - For tractors using Delco-Remy distributors only
|
ABC170 Autolite Spark Plug - 18 mm thread diameter 1/2" reach 7/8" hex Medium hot Std Tip / Resistor Plug gap 0.025"
|
MFS096 Ignition Tune-Up Kit - Fits Delco Distributor w/ clip held cap 4 cylinder models ONLY Contains spark plugs, heavy duty points, condenser, and rotor button Spark plug thread size is 18 MM diameter 1/2" Reach and 7/8" Hex
|
EIGN01 Electronic Ignition Kit, 6 Volt positive Ground System, 4 cyl Delco distributor with clips
|
EIGN19 Electronic Ignition Conversion Kit - 12 volt Negative Ground System 4 cyl Delco distributor with clips
|
EIGN25 Electronic Ignition Kit - 12 Volt Negative Ground w/ Delco Distributor
|
ABC520 Delco Rotor Button - Tractors using Delco-Remy distributors with clip held cap through 1963
|
ABC186 Distributor Dust Cover With Felt Gasket And Washer - Fits tractors using Delco-Remy distributors with clip held cap thru 1963
|
ABC488L Spring Clip And Longer Bracket - Distributor caps use one each of ABC488L & ABC488S FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC488S Spring Clip And Shorter Bracket - Distributor caps use one each of ABC488L & ABC488S - FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC2523 Distributor Hold Down Clamp - For 3/8" hold down bolt. 2 used per engine, sold individually.
|
ABC3007 Delco Distributor Shaft Bushing and Shim Kit - has an 0.486" I.D., 0.656" O.D. and 2.867" length. Bushing must be sized to shaft after installation
|
ABC500 Delco Distributor Terminal Insulator - Square was the late style that fit distributor housings with .300 Dia hole with a keyway, WILL NOT FIT IH BUILT DISTRIBUTORS/MAGNETOS
|
ABC011 6 Volt Distributor Coil - Metal housing, mounting bracket included-- fits tractors with barrel-type coil
|
|
ABC348 Vertical Hot Coil 12 Volt Externally Resisted 55000 - Delco distributors WITH SCREW HELD CAP --- Kit contains: Heavy duty point set vibration resistant condenser and rotor
|
ABC4293 6 Volt Flame Thrower Coil - Use with electronic ignition kits or breaker point ignitions Note: Do not use an external resistor on 6 volt electrical systems
|
ABC509 12V Coil Internal Resisted - Barrel style Internally resisted Includes coil mounting bracket
|
R3528 12 Volt Flame Thrower Coil - for all 12 volt systems requiring horizontal mounting position - Internally Resisted 3 OHMS.
|
ABC366 2 Terminal Style Universal 12-volt Voltage - 2 terminal style Reduces voltage to distributor points 2.0 OHMS of resistance, Limits voltage to coil when using 12-volt battery.
|
ACS228 Spark Plug Wire Set - Dimensions= (approximately) 2 wires= 32", 1 wire= 34 1/2", 1 wire = 38", & coil wire = 24" The coil wire is made from excess wire left over from the spark plug wire.
|
ACS287 Spark Plug Wire Set - These wires have a copper core with aluminum coating to prevent corrosion. PRE ASSEMBLED, WITH WATERPROOF NEOPRENE
|
FDS149 Spark Plug Wiring Set 4 Cylinder - This spark plug wires set fits most 4 cylinder models. They have copper core wires with aluminum coating to prevent corrosion. And 90 degree boots.
|
ABC4291 Spark Plug Wiring Set with Straight Boots, 4-cyl. - Use with electronic ignitions
|
ABC4309 Spark Plug Wiring Set for Electronic Ignition with 90 degree Boots -
|
ACS4304 Spark Plug Wiring Set 4 Cyl. - Pre-Assembled with Straight Boots
|
MAG6 Wico XH And XHD Magneto Service
|
KEY01 Ignition Key Verify key style before ordering, as more than one style could be used
|