JDS556 Left Hand Spark Plug Cover
|
JDS558 Right Hand Spark Plug Cover With Grommet
|
ABC018 - Delco Clip Held Ignition Kit - For use on tractors using Delco-Remy distributors with clip held cap through 1963 Delco Distributors Only
|
JDS268 Ignition Tune-Up Kit - For DELCO distributors only Using 18 MM, 1/2" Reach 7/8" Hex Spark Plugs Kit contains: Rotor, Points, Condenser, (2) Spark Plugs Will NOT fit magneto ignitions.
|
EIGN18 Electronic Ignition Conversion Kit - 12 Volt Positive Ground System w Delco Distributor
|
EIGN21 Electronic Ignition Conversion Kit - 12 Volt Negative Ground System w/ Delco Distributor
|
ABC520 Delco Rotor Button - Tractors using Delco-Remy distributors with clip held cap through 1963
|
ABC186 Distributor Dust Cover With Felt Gasket And Washer - Fits tractors using Delco-Remy distributors with clip held cap thru 1963
|
JDS585 Distributor Cap - Fits John Deere - 520, 530, 620, 630, 720, 730 with Delco Distributor Clip Held Cap For Vertical Distributors
|
|
ABC488L Spring Clip And Longer Bracket - Distributor caps use one each of ABC488L & ABC488S FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC488S Spring Clip And Shorter Bracket - Distributor caps use one each of ABC488L & ABC488S - FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC2523 Distributor Hold Down Clamp - For 3/8" hold down bolt. 2 used per engine, sold individually.
|
ABC3007 Delco Distributor Shaft Bushing and Shim Kit - has an 0.486" I.D., 0.656" O.D. and 2.867" length. Bushing must be sized to shaft after installation
|
ABC500 Delco Distributor Terminal Insulator - Square was the late style that fit distributor housings with .300 Dia hole with a keyway, WILL NOT FIT IH BUILT DISTRIBUTORS/MAGNETOS
|
|
ABC348 Vertical Hot Coil 12 Volt Externally Resisted 55000 - Delco distributors WITH SCREW HELD CAP --- Kit contains: Heavy duty point set vibration resistant condenser and rotor
|
ABC509 12V Coil Internal Resisted - Barrel style Internally resisted Includes coil mounting bracket
|
R3528 12 Volt Flame Thrower Coil - for all 12 volt systems requiring horizontal mounting position - Internally Resisted 3 OHMS.
|
ABC366 2 Terminal Style Universal 12-volt Voltage - 2 terminal style Reduces voltage to distributor points 2.0 OHMS of resistance, Limits voltage to coil when using 12-volt battery.
|
ABC170 Autolite Spark Plug - 18 mm thread diameter 1/2" reach 7/8" hex Medium hot Std Tip / Resistor Plug gap 0.025"
|
ABC171 Autolite Spark Plug - 18mm thread diameter 1/2" reach 7/8" hex Hot heat range Std Tip / Resistor
|
JDS643 Spark Plug Wiring Set With Copper Wire - These wires are approx. 32 & 49" long, have a copper core with aluminum coating to prevent corrosion and a Neoprene Outer Cover.
|
JDS4335 Spark Plug Wiring Set with 90 degree Boots, 2-cyl. - Used with Electronic Ignition Kits - EIGN07, EIGN18, EIGN20, EIGN21
|
ABC3978 Ignition Points Only (for Delco Distributor with Clip Held Cap) - For tractors using Delco-Remy distributors only
|
ABC065 Ignition Key Switch 3/4" diameter thread On some applications must drill hole to 0.800" 2 wire Includes 2 keys
|
ABC400 Ignition Key Switch - For battery ignition only, 3/4" Dia thread, 4 terminals --- 4 position switch, has 4 stud terminals --- Includes 2 keys
|
IHS760 Ignition Key Switch 2 spade terminals. For use in 0.800" diameter hole.
|
ABC398 Universal 2 Position Push Pull Ignition and Light Switch The knob measures 10-24 NC thread pitch. The threaded stem measures 3/8 - 24 UNF.
|
ABC489 Magneto Push Pull Switch This switch has 1 screw type terminal. This switch will fit most models with a magneto ignition. The threaded stem measures 3/8 - 32 UNEF.
|