ABC018 - Delco Clip Held Ignition Kit - For use on tractors using Delco-Remy distributors with clip held cap through 1963 Delco Distributors Only
|
ABC4408 Ignition Tune Up Kit without Rotor - For Delco Distributors listed with Screw Held Caps
|
ABC333 Ignition Tune-Up Kit - Delco distributors WITH SCREW HELD CAP --- Kit contains: Heavy duty point set vibration resistant condenser and rotor
|
EIGN09 Electronic Ignition Conversion Kit - 12 Volt Positive Ground System, with Delco Distributor and Screw Held Cap and Clockwise Rotation - Check your Distributor Number Before Ordering
|
EIGN24 Electronic Ignition Kit - 12 Volt Negative Ground w Delco Distributor with Screw Held Cap and Counter Clockwise Rotation - Check your Distributor Number Before Ordering
|
R3525 Electronic Ignition Kit - 12 Volt Positve Ground w Delco Distributor with Screw Held Cap Check your Distributor Number Before Ordering
|
EIGN26 Electronic Ignition Kit - 12 Volt Negative Ground w/ Delco Distributor with Screw Held Cap and with Counter Clockwise Rotation - Check your Distributor Number Before Ordering
|
ABC520 Delco Rotor Button - Tractors using Delco-Remy distributors with clip held cap through 1963
|
ABC141 Distributor Cap - For 4 Cyl. Delco Distributor with screw help cap (1963 & up)
|
ABC186 Distributor Dust Cover With Felt Gasket And Washer - Fits tractors using Delco-Remy distributors with clip held cap thru 1963
|
ABC276 Distributor Cap - Fit tractors using Delco-Remy distributors with clip held cap through 1963.
|
ABC420 Delco Screw Held 6 Cylinder Distributor Cap
|
ABC2428 Delco Distributor Dust Cover Screw Held - 3.300" OD, 1.047" tall, (2) 0.210" screw holes Fits IH Delco distributor numbers: 1112477, 1112489, 1112697.
|
|
ABC488L Spring Clip And Longer Bracket - Distributor caps use one each of ABC488L & ABC488S FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC488S Spring Clip And Shorter Bracket - Distributor caps use one each of ABC488L & ABC488S - FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC2523 Distributor Hold Down Clamp - For 3/8" hold down bolt. 2 used per engine, sold individually.
|
ABC3007 Delco Distributor Shaft Bushing and Shim Kit - has an 0.486" I.D., 0.656" O.D. and 2.867" length. Bushing must be sized to shaft after installation
|
|
ABC348 Vertical Hot Coil 12 Volt Externally Resisted 55000 - Delco distributors WITH SCREW HELD CAP --- Kit contains: Heavy duty point set vibration resistant condenser and rotor
|
ABC509 12V Coil Internal Resisted - Barrel style Internally resisted Includes coil mounting bracket
|
R3528 12 Volt Flame Thrower Coil - for all 12 volt systems requiring horizontal mounting position - Internally Resisted 3 OHMS.
|
ABC366 2 Terminal Style Universal 12-volt Voltage - 2 terminal style Reduces voltage to distributor points 2.0 OHMS of resistance, Limits voltage to coil when using 12-volt battery.
|
ABC170 Autolite Spark Plug - 18 mm thread diameter 1/2" reach 7/8" hex Medium hot Std Tip / Resistor Plug gap 0.025"
|
ABC2863 Spark Plug Wire Set - This wiring set is cut to length, has waterproof neoprene, has 7 mm "tinned" copper core, and includes the coil wire
|
ABC326 Spark Plug Wire Set 6 Cylinder - Copper Core. 35" long waterproof neoprene w/ 90 degree boots. You will have to cut the wires to your desired length & Crimp End W/ A Crimping Tool.
|
ABC5841 Spark Plug Wiring Set w/ Straight Boots, 6 cyl.
|
ACS228 Spark Plug Wire Set - Dimensions= (approximately) 2 wires= 32", 1 wire= 34 1/2", 1 wire = 38", & coil wire = 24" The coil wire is made from excess wire left over from the spark plug wire.
|
FDS149 Spark Plug Wiring Set 4 Cylinder - This spark plug wires set fits most 4 cylinder models. They have copper core wires with aluminum coating to prevent corrosion. And 90 degree boots.
|
ABC4291 Spark Plug Wiring Set with Straight Boots, 4-cyl. - Use with electronic ignitions
|