ABC6165 Premium Distributor Cap - USA Made
|
IHS5713 Distributor Gasket - USA Made
|
EIGN199 Electronic Ignition II Conversion Kit, 12 Volt Negative Ground 4 Cyl Delco Distributor with clip mounted cap - USA Made
|
ABC6411 Flame-Thrower II Ignition Coil - USA Made
|
ABC018 - Delco Clip Held Ignition Kit - For use on tractors using Delco-Remy distributors with clip held cap through 1963 Delco Distributors Only
|
ACS110 Ignition Tune Up Kit - FITS DELCO DISTRIBUTOR ONLY, Except Delco distributor 1112688 - contains: Spark plugs (with 3/8" reach), heavy duty points, condenser, rotor - - Check!! Spark Plug Gap = .030, Point Gap = .020, Fits 4 cyl Gas engines
|
ABC3978 Ignition Points Only (for Delco Distributor with Clip Held Cap) - For tractors using Delco-Remy distributors only
|
ABC168 Autolite Spark Plug - 14 mm thread diameter 3/8" reach 13/16" hex Medium hot Standard tip/non resistor
|
EIGN01 Electronic Ignition Kit, 6 Volt positive Ground System, 4 cyl Delco distributor with clips - USA MADE
|
EIGN19 Electronic Ignition Conversion Kit - 12 volt Negative Ground System 4 cyl Delco distributor with clips - USA MADE
|
ABC520 Delco Rotor Button - Tractors using Delco-Remy distributors with clip held cap through 1963
|
ABC276 Distributor Cap - Fit tractors using Delco-Remy distributors with clip held cap through 1963.
|
ABC186 Distributor Dust Cover With Felt Gasket And Washer - Fits tractors using Delco-Remy distributors with clip held cap thru 1963
|
|
ABC488L Spring Clip And Longer Bracket - Distributor caps use one each of ABC488L & ABC488S FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC488S Spring Clip And Shorter Bracket - Distributor caps use one each of ABC488L & ABC488S - FITS DELCO DISTRIBUTORS ONLY, *** WILL NOT FIT IH OR AUTOLITE BUILT DISTRIBUTORS/MAGNETOS **
|
ABC2523 Distributor Hold Down Clamp - Used when converting from Magneto to Delco Distributor
|
ABC3007 Delco Distributor Shaft Bushing and Shim Kit - has an 0.486" I.D., 0.656" O.D. and 2.867" length. Bushing must be sized to shaft after installation
|
ABC500 Delco Distributor Terminal Insulator - Square was the late style that fit distributor housings with .300 Dia hole with a keyway, WILL NOT FIT IH BUILT DISTRIBUTORS/MAGNETOS
|
ABC011 6 Volt Distributor Coil - Metal housing, mounting bracket included-- fits tractors with barrel-type coil
|
|
ABC348 12 Volt Distributor 'HOT' Coil (55000 Volts)
|
ABC4293 6 Volt Flame Thrower Coil - Use with electronic ignition kits or breaker point ignitions Note: Do not use an external resistor on 6 volt electrical systems
|
ABC6158 12 Volt Distributor 'HOT' Coil (55000-Volts)
|
ABC509 12V Coil Internal Resisted - Barrel style Internally resisted Includes coil mounting bracket
|
R3528 12 Volt Flame Thrower Coil - for all 12 volt systems requiring horizontal mounting position - Internally Resisted 3 OHMS.
|
ABC366 2 Terminal Style Universal 12-volt Voltage - 2 terminal style Reduces voltage to distributor points 2.0 OHMS of resistance, Limits voltage to coil when using 12-volt battery.
|
ACS1552 Tailered Spark Plug Wire Set - Original type preassembled with cotton braid copper wire. 5 wires measure 7-1/4", 9-3/4", 12-1/4", 16-3/4" and 13" coil wire.
|
ACS228 Spark Plug Wire Set - Dimensions= (approximately) 2 wires= 32", 1 wire= 34 1/2", 1 wire = 38", & coil wire = 24" The coil wire is made from excess wire left over from the spark plug wire.
|
ACS287 Spark Plug Wire Set - These wires have a copper core with aluminum coating to prevent corrosion. PRE ASSEMBLED, WITH WATERPROOF NEOPRENE
|