IHS1307 Belt Pulley Gear Box Oil Seal
 IHS1307 Oil Seal - 1.875" I.D., 2.627" O.D., 0.312" wide  |
|
Item Number: IHS1307
|
IHS1307 Belt Pully Gearbox Oil Seal International / Farmall - Fits: Fits following as a belt pulley gearbox seal: 300, 350, 460, H, HV, I4, I6, ID6, Super H, Super HV, [M, MD, MDV, MV (Fits some of the following to SN 19202 as a belt pulley gearbox seal {Measure BEFORE ordering as there were two (2) different sizes}]Super W4, W4, W6, WD6, Fits following as a transmission drive shaft seal for tractors without torque amplifier or independent pro drive: 300, 330, 340, 350, 460, Fits following gas/Lp as a front crankshaft seal;: 100, 130, 140, 154, 184, 185, 200, 230, 240, 330, 340, 404, 424, 444, 504, A, AV, B, BN, C, Cub, Cub Loboy, Super A, Super AV, Super C, T340, T5, Fits some of the following to Sn: 19202 as a belt pulley gearbox seal (measure BEFORE ordering as there were 2 different sizes).: M, MD, MDV, MV; Replaces: 358783R91, 358822R91, 363821R91, 367731R11, 378193R91, 389407R2, 389407R92, 43442D, 46122DAX, 46122DBX, 46122DCX, 46122DXA, 49177D White - Fits: Fits following when used as a PTO output shaft seal (all with 1000 RPM single PTO): 2-135, 2-155, 2-180, 2-70, 4-210, 4-225; Replaces: 803551, 70937160, 71353831, 72160018 1.875" I.D., 2.627" O.D., 0.312" wide |
IHS925 Winged Radiator Drain Cap - 3/8" pipe thread, has "IH" stamped into it, includes gasket, Cast Iron with ZINC Plating - USA Made
|
IHS145GK Cub, 154, 184, 185 Manifold Gasket Set
|
ABC2308 Manifold Washer - 3/8"
|
IHS2284 Manifold High Nut - Early H, M & others - 3/8" - 24" NF, 0.535" tall, 9/16" hex.
|
IHS543 Starter Hand Crank - 13-1/4" TO FIRST BEND
|
ABC093 Oil Filter Element - 3-15/16" H x 2.5" W Cartridge type filter
|
ABC540 Washer / Gasket For Oil Pan Drain Plug - Copper, .875" ID, 1.110" OD, .050" Thick
|
ABC539 Oil Pan Drain Plug - 7/8" - 18 UNF
|
IHS1929 Flywheel Ring Gear - 84 Teeth. Measures 9.495" Inside diameter and 10.678" Outside diameter.
|
IHS1234 Cub 154 & 185 Loboy Clutch Pressure Plate
|
IHS2391 Valve Tappet Side Cover Gasket - Fits Cub, Cub Loboy, 154, 184, 185 - USA Made
|
IHS1324 Complete Engine Gasket Set - Fits Cub, 154, 184, 185 w/ C60 engines rear seal - USA Made
|
IHS2343 Crankcase Front Cover Gasket - Fits Cub (up to SN: 139516)
|
IHS2350 Crankcase Front Cover Gasket
|
IHS005VGK Cylinder Head Gasket Set - International / Farmall - Fits: Cub, 154, [ 184, 185 (except carb mounting gasket) ]
|
IHS3242 Farmall Cub Rebore Kit 0.040" overbore - Fits Cub, Cub Loboy Up to engine SN: 264567
|
IHS3238 Rebore Kit (0.030" overbore)
|
IHS3246 Farmall Cub Rebore Kit 0.060 overbore - Fits Cub, Cub Lo Boy Up to engine SN: 264567
|
IHS3235 Rebore Kit (0.020" overbore)
|
IHS2104 Piston Ring Set - Fits Standard Bore
|
IHS2108 Piston Ring Set - Fits 0.040" overbore, 2.665" bore
|
IHS2106 Piston Ring Set - Fits 0.020" overbore, 2.645" bore
|
IHS3738 Piston Wrist Pin Bushing - Fits Cub, Cub Loboy, 154, 184, 185
|
IHS2396 Crankshaft Rear Oil Seal Retainer Gasket - Fits Farmall Cub, Cub Loboy, U1, 154, 184, 185 - USA Made
|
IHS2387 Rear Crankshaft Seal - Fits Farmall Cub, Cub Loboy, U1, 154, 184, 185 designed to fit both early and late seal retainers - USA Made
|
IHS1945 Standard Rod Bearing Kit - USA Made
|
IHS2538 Connecting Rod Bearing - 0.010" (1.489") undersize rod journal
|
IHS2540 Connecting Rod Bearing - 0.020" (1.479") undersize rod journal
|
IHS2542 Connecting Rod Bearing - 0.010" (1.489") undersize rod journal
|
IHS3217 Standard Rod Bearing, Standard - Fits Cub, Cub Loboy, 154, 184, 185 ('late' 1968 and up)
|
|
|