Lights & Parts
|
|
IHS464 Light Clamp For front or rear light --- powder coated red
|
IHS992 Cast Iron Light Clamp Fits C, H, M & more
|
IHS623 4 Position 6 Volt Rotary Light Switch (OEM) - USA MADE
|
IHS622 3 Position 6 Volt Rotary Light Switch (OEM) - USA MADE
|
IHS624 3 Position 12 Volt Rotary Light Switch (OEM) - USA MADE
|
IHS625 4 Position Switch Body Only - 12 Volt USA MADE
|
IHS1636 Rotary 4 Position Light Switch For models with 6 Volt, CUT OUT relay, NOT voltage regulator.
|
IHS593 6 Volt Rotary Light Switch 4 Position - USA Made
|
IHS594 12 Volt Rotary Light Switch 4 Position - USA Made
|
IHS595 6 Volt Rotary Light Switch 3 Position - Fits A, AV, B, BN, C, Cub, H, HV, I4, I6, I9, ID6, ID9, M, MD, MDV, MV, [Super A, AV, C, H, HV, M, MD, MDV, MV, W4, W6,] W4, W6, W9, WD6, WD9, WDR9, WR9 (WITH switch on taillight & Regulator)
|
IHS596 12 Volt 3 Position Rotary Light Switch - Fits A, AV, B, BN, C, Cub, H, HV, I4, I6, I9, ID6, ID9, M, MD, MDV, MV, [Super A, AV, C, H, HV, M, MD, MDV, MV, W4, W6,] W4, W6, W9, WD6, WD9, WDR9, WR9 (WITH switch on taillight & Regulator)
|
IHS598 6 Volt Rotary Light Switch 4 Position - Fits Cub, Cub LoBoy, T340, T4, T5, 140, 240, 340
|
IHS599 12 Volt Rotary Light Switch 4 Position 0.670" O.D. thread
|
IHS788 4 Position Rotary Light Switch O.E.M. - Fits Cub, Cub Loboy, T340, TD340, 1206, 140, 154, 184, 185, 2424, 2444, 2500A, 574, 3414, 3444, 3514, 354, 3600, 3616, 3800, 3850, 404, 4100, 4156, 424, 444, 454, 464, 504, 606, 674, 706, 806 USA MADE
|
IHS918 Light Switch Combo With Knob Also fits original lights. 3 screw terminals
|
IHS351R Complete Headlight Assembly his 6 volt lamp assembly is 4-3/4" in diameter and arrives with a beautiful red powder coat finish. ** Threaded Stud Length = 2-1/2" **
|
IHS351R12V Complete Headlight Assembly This headlight assembly measures 4-3/4" Powder coated red 12 volt bulb Threaded stud length: 2-1/2"
|
IHS460 Flat Back Headlight Assembly 6 Volt Restoration Quality - Flatback Headlights were used early 1953 & up; 4-5/8" lens width. Please note this light is only correct for models with 6 volt systems.
|
IHS463 Flat Back Headlight Assembly 12 Volt Restoration Quality. - Flatback Headlights were use early 1953 & UP; 4-5/8" lens width. Please note this light is only correct for models with 12 volt systems.
|
IHS462 Flatback Headlight Gasket - 4-5/8"
|
IHS461 Flat Back Headlight Trim Ring 4-5/8" diameter. This trim ring will fit OEM sealed beam headlights and our IHS460 and IHS463 Headlamp assemblies.
|
ABC560 Headlight Rubber Gasket (Modern version of IHS355 --- Black rubber --- This gasket is one continuous piece (No staples), therefore it will seal better than the original style)
|
ABC320 Headlight Reflector This reflector is Interchangeable with your original and measures 4 1/2" or 4 3/4", depending on how you measure (directly across the top of the housing, or over the curve of the lense.)
|
ABC3028 Rubber Light Bezel Without Guard This bezel has 3 outer tabs to attach rubber ring to the light housing, and there are 4 inner tabs to secure to the sealed beam
|
IHS352 Curved Lens With Guide Name "GUIDE" DISPLAYS NEAR BOTTOM OF LENS --- INTERCHANGEABLE WITH THE ORIGINAL --- DIMPLED OUTER SURFACE
|
IHS353R Red Headlight Trim Ring RED FINISH, INTERCHANGEABLE with ORIGINAL LIGHTS.
|
IHS355 Headlight Gasket BLACK RUBBER, LIKE ORIGINAL WITH STAPLE --- FOR USE IN 4-3/4" DIAMETER LIGHT ASSEMBLY
|
ABC344 6 Volt Tail Light Bulb is interchangeable with the original light using a 12 volt system --- 12-V, 12 amp, 1.73 watt Miniature Bayonet Base ---
|
ABC353 12-volt sealed lo-beam Lamp
|
|
|