ABC398 Universal 2 Position Push Pull Ignition and Light Switch The knob measures 10-24 NC thread pitch. The threaded stem measures 3/8 - 24 UNF.
|
JDS631 3 Position Fused Starter and Light Switch - Only fit models that use a voltage regulator. 15 amps and has 5 terminals, knob 10-24 NC threads. The threaded stem measures 7/16 - 20 UNF.
|
ABC4279 3 Position Push/Pull Light Switch
|
IHS622 3 Position Switch Body Only 6 Volt
|
IHS1636 Rotary 4 Position Light Switch For models with 6 Volt, CUT OUT relay, NOT voltage regulator.
|
IHS593 6 Volt Rotary Light Switch 4 Position THIS SWITCH IS FOR TRACTORS WITHOUT A SWITCH ON THE TAIL LIGHT. 0.670" O.D. thread
|
IHS594 12 Volt Rotary Light Switch 4 Position THIS SWITCH IS FOR TRACTORS WITHOUT A SWITCH ON THE TAIL LIGHT. . 0.670" O.D. thread
|
IHS595 6 Volt Rotary Light Switch 3 Position - FOR TRACTORS WITH REGULATORS ONLY Includes OLD STYLE KNOB --- 3 POSITION
|
IHS596 12 Volt 3 Position Rotary Light Switch - FOR TRACTORS WITH SWITCH ON REAR LIGHT
|
IHS598 6 Volt Rotary Light Switch 4 Position 0.670" O.D. thread
|
IHS788 4 Position Rotary Light Switch O.E.M. switch 5 outer terminals plus resistor 4 position 0.670" O.D. thread
|
IHS918 Light Switch Combo With Knob Also fits original lights. 3 screw terminals
|
IHS351R Complete Headlight Assembly his 6 volt lamp assembly is 4-3/4" in diameter and arrives with a beautiful red powder coat finish. ** Threaded Stud Length = 2-1/2" **
|
IHS351R12V Complete Headlight Assembly This headlight assembly measures 4-3/4" Powder coated red 12 volt bulb Threaded stud length: 2-1/2"
|
JDS468 Sealed Beam Head Light 6 Volt Bottom mounting stud. 1/2" x 14 threads For 12 volt applications you must also order ABC353
|
IHS460 Flat Back Headlight Assembly 6 Volt Restoration Quality - Flatback Headlights were used early 1953 & up; 4-5/8" lens width. Please note this light is only correct for models with 6 volt systems.
|
IHS463 Flat Back Headlight Assembly 12 Volt Restoration Quality. - Flatback Headlights were use early 1953 & UP; 4-5/8" lens width. Please note this light is only correct for models with 12 volt systems.
|
IHS462 Flatback Headlight Gasket Only 4-5/8" his headlight gasket will fit the original factory sealed beam lights and also the serviceable flatback headlights sold by Steiner Tractor Parts (IHS460 & IHS463)
|
IHS461 Flat Back Headlight Trim Ring 4-5/8" diameter. This trim ring will fit OEM sealed beam headlights and our IHS460 and IHS463 Headlamp assemblies.
|
ABC560 Headlight Rubber Gasket (Modern version of IHS355 --- Black rubber --- This gasket is one continuous piece (No staples), therefore it will seal better than the original style)
|
ABC320 Headlight Reflector This reflector is Interchangeable with your original and measures 4 1/2" or 4 3/4", depending on how you measure (directly across the top of the housing, or over the curve of the lense.)
|
IHS352 Curved Lens With Guide Name "GUIDE" DISPLAYS NEAR BOTTOM OF LENS --- INTERCHANGEABLE WITH THE ORIGINAL --- DIMPLED OUTER SURFACE
|
IHS353R Red Headlight Trim Ring RED FINISH, INTERCHANGEABLE with ORIGINAL LIGHTS.
|
IHS355 Headlight Gasket BLACK RUBBER, LIKE ORIGINAL WITH STAPLE --- FOR USE IN 4-3/4" DIAMETER LIGHT ASSEMBLY
|
IHS464 Light Clamp For front or rear light --- powder coated red
|
IHS557 Front Light Bracket With Nut And Washer 2 required per tractor; sold individually
|
JDS676 Clamp Ring With Screw .885" wide
|
IHS2933 3 Terminal Junction Block has (3) 10 - 32 studs and 3" center-to-center mounting holes.
|
ABC344 6 Volt Tail Light Bulb is interchangeable with the original light using a 12 volt system --- 12-V, 12 amp, 1.73 watt Miniature Bayonet Base ---
|
ABC343 12 Volt Rear Combo Light Bulb is interchangeable with the original light using a 12 volt system --- 12-V, 12 amp, 1.73 watt Miniature Bayonet Base ---
|