ABC4279 3 Position Push/Pull Light Switch
|
ABC425 Knob For Light Switch Says: "Lights"Thread size: 10-32
|
ACS139 Light Switch 3 Position Hi charge with lights Note: Switch manufacturers consider OFF as 1 position 0.800" diameter thread end, 10-32 thread Three screw type terminals
|
ACS152 6 Volt Headlight Assembly 1/2" diameter stud --- 4 3/4" Dia. curved lens --- 6 Volt---If you need 12 Volt order ACS205 instead.
|
ACS205 Headlight Assy, 12 Volt includes a black powder coat finish and a 4-3/4" diameter curved lens.
|
ABC560 Headlight Rubber Gasket (Modern version of IHS355 --- Black rubber --- This gasket is one continuous piece (No staples), therefore it will seal better than the original style)
|
ABC320 Headlight Reflector This reflector is Interchangeable with your original and measures 4 1/2" or 4 3/4", depending on how you measure (directly across the top of the housing, or over the curve of the lense.)
|
IHS352 Curved Lens With Guide Name "GUIDE" DISPLAYS NEAR BOTTOM OF LENS --- INTERCHANGEABLE WITH THE ORIGINAL --- DIMPLED OUTER SURFACE
|
IHS353B Headlight Ring BLACK FINISH --- INTERCHANGEABLE WITH ORIGINAL
|
IHS353R Red Headlight Trim Ring RED FINISH, INTERCHANGEABLE with ORIGINAL LIGHTS.
|
IHS355 Headlight Gasket BLACK RUBBER, LIKE ORIGINAL WITH STAPLE --- FOR USE IN 4-3/4" DIAMETER LIGHT ASSEMBLY
|
ABC1439 6 Volt Light Bulb For models listed that take a double element, double contact base
|
ABC344 6 Volt Tail Light Bulb is interchangeable with the original light using a 12 volt system --- 12-V, 12 amp, 1.73 watt Miniature Bayonet Base ---
|
ABC388 4-3/4 smooth glass Lens with Guide name
|
IHS354 6 Volt Light Bulb 6 Volt Single contact base 24 WattInterchangeable with originalFits as a headlight or a rear combo light bulb
|
IHS436 12 Volt Light Bulb INTERCHANGEABLE WITH ORIGINAL --- FITS AS A HEADLIGHT OR A REAR COMBO LIGHT BULB
|
ABC3857 LED Light Bulb Works for both 6 volt and 12 volt sytems
|
ACS123 Red Glass Tail Light Lens ACS264V6, ACS264V12 & ACS099 tail lights are interchangable with the original --- Any AC with bullet style tail light
|
ACS264V12 12 Volt Tail Light Taillight will fit any Allis Chalmers tractor as well as other brands that are using a bullet-style tail light with a 2-1/8" OD lens. This light assembly includes the red glass lens
|
ACS264V6 6 Volt Tail Light Will fit Allis Chalmers and others with bullet-style tail light and 2-1/8" O.D. lens Restoration quality 6-Volt bulb included Red glass lens Includes base gasket
|
ABC3538 12-Volt LED Fender and Cab Warning Light
|
ABC4098 LED Fender and Cab Mount Warning Light - 4-1/2" x 4-1/2", Voltage: 10-30 Volt operating range
|
ABC1979 Tail Light Base Gasket
|
IHS475 Light Terminal This terminal assembly will interchange with the original.
|
OLS072 Tail Light Gasket RUBBER GASKET - INTERCHANGEABLE WITH THE ORIGINAL CORK GASKET
|
OLS071 Tail Light Trim Ring Dimensions = 2.292" O.D & 1.640" I.D.
|
ABC3514 12-Volt LED Flood Light Assembly 4-1/4" chrome die cast with acrylic lens.
|
ABC3899 LED Flasher Unit 0.230" dia. single bolt
|
IHS950 Field Resistor On Light Switch - for the listed models with a cut out relay on the generator. The resistor is not used on tractors with voltage regulators.
| |